Hauled again, this is getting ridiculous now

We are hauled, and awaiting repair.

Not long after we anchored the sun set and the fishnets we anchored off moved a lot closer. I have noticed this before, at night hazards always seem to move closer, not sure if this is an optical or psychological effect, either way, it’s a pain, we moved very close to the nets, and I made a good note of where we are by taking transits around the area, that basically means lining up the edges of the net with something on the land, and making sure they stay lined up. Of course, a few hours later the tide turned, we swung and ended up even closer to the nets, which was odd as I thought we should have gone further away. I told Kathy we might need to re anchor, but I sat on the bowsprit for 20 minutes, enjoying the fading light and watching my transits, only to decide we were safe. After a lovely pasta & pesto dinner, I went to sleep in the cockpit, waking every hour or so to check my transits, until at 3am, when the tide swung us again, back to roughly were we started, then I slept through to sunrise.

Looking over to the yard, I could just make out the route in, but it looked shallow, sticks in the mud showed the way and later I watched a motor boat make its way in which gave me a boost.

The nets looked amazing in the morning sun, they are all different coloured 5 gallon plastic containers, large jerry can size.

These drums above on the right are spares I think, they were about 40ft to our stern. This is what you can see from space, credit to google earth.

So just 30 minutes before high water we headed in, Kathy called out the depth. We started with a metre more than when we went aground, so I was optimistic, however we soon hit 2 metres, but were still going, we should be aground at 2 metres, but I added a little into the calibration of the meter to help, but when we reached 1.8 I was wondering how we were still going forward, whatever was under us must have been very soft, so I upped the revs, and we raced in, I figured if I was going aground I wanted to plough through, into the deeper water in the boatyard. It quickly went back to 2 metres and stayed around that for the short trip to tie up alongside in front of the travel lift.

Once tied up, the first of several disappointments arrived, I was told the travel lift is to small to take us in the normal way, so I had to drop the backstay, remove the wind generator and reverse into the travel lift. I didn’t want to do the backstay as it’s going to be difficult to get it back together without loosening the forestays, which means taking the headsails off and removing the furling drum.  I will have to think of a cunning plan, probably involving rope and pulleys.

I managed to keep the wind generator on, the problem would come later once we were on land, then the travel lift wouldn’t be able to escape without decapitating the turbine, and that’s normally my job, using a fishing rod or forehead. To turn the boat around, a man was dispatched into the water to push it around, A dinghy might have been better, but who am I to judge.

The next blow was that rather than change the bearing and launch in the morning, I was told that they couldn’t start today as planned, as they had to do another boat in an emergency, and that tomorrow is national holiday, but they could start on Thursday. So the earliest we can launch will be Friday, I expect it will end up being Saturday. The tides are good until next Monday, after that we can’t get our for another week or more.

I was able to see that some more rubber had worked it’s way out of the cutless bearing, you can see a strip of it here, I have pulled it out to see better, but it didn’t take any effort, so I’m assuming it’s a bit of a mess inside the bearing.
I removed the blades and vane off the turbine so they can get the travel lift away, then I set about doing the job myself, I thought perhaps I could get the prop off, and pull the prop shaft, making it easier for them, I’m still going to be paying them, whoever does the work, but at least this way I might get away earlier. The prop came off no problem, but the PSS dripless shaft seal won’t come off. This is a device that stops the water getting into the boat through the tube that the prop shaft goes out of the boat through. It seems that the LBM engineer, who was the last one near it, had stripped one of the 2 allen grub screws that holds it in place. This is a tiny grub screw made of 316 stainless steel, inside a block of 316 stainless steel, in the bottom of the boat in a most inaccessible place.I’m at the point of drilling it out, but that might damage the seal, and I might end up having to wait a few weeks to get a replacement shipped in, so I’m going to wait until the yard’s engineer turns up, and get him to sort it. Good engineers know how to sort these things. I once had a similar problem on the baba 30 which required me to cut the prop shaft in half to get the job done, I really don’t want to go down that road again.

I forgot to add this AIS chart yesterday, you can see us as the little boat with the white dot, down in the middle, working our way east and edging across the channel getting ready to hang a left up to the eastern buoy and back into Malaysian waters. You can see it’s busy, each triangle is a boat, mostly big tankers or container ships, doing between 5 and 20 knots.

As it’s a holiday tomorrow, Kathy and I will pop into Johor Bahru and check it out, it’s supposed to be a bit of a party town, so I better get my John Travolta suit out, just in case we go dancing 😉

Paul Collister

 

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.